MSK10AL-P-253
Processing length 300–2500 mm, Working width 32–672 mm, Board thickness 8–50 mm, Spindles 220.
Features
CNC Multi-spindle Drilling Machine — structure and configuration
Five faces in one clamping
The top face plus the front, rear and both side faces are drilled in one clamping — no panel turnover and no second set-up.
Double-station feed
Belt or chain feeding runs through stations P1 and P2, so one side drills while the other is loaded.
Scan to run
QR / barcode scanning turns MPR and DXF drawings into machining programs, so changeover needs no manual programming.
Five faces, one clamping
Top face plus four sides in one set-up; the bottom face is not drilled
Swipe sideways to see the full diagram
Top face
Vertical feed; face holes in one pass
Right side
Horizontal feed
Rear side
Horizontal feed
Left side
Horizontal feed · hidden by the panel in the drawing
Front side
Horizontal feed · hidden by the panel in the drawing
Conventional route
Several panel turnovers, re-clamping and re-datum each time, so errors stack up
MSK10AL-P-253
One clamping, 5 faces drilled in sequence from the same datum
The drawing is a generic isometric sketch of a panel, not to scale; arrows show the drilling direction. The actual drill-unit layout of this model is given in the specification table.
Machine photo
Product photo of this model
Note: the image is the product photo of this model and is for reference only; the delivered machine prevails.
Main functions
Captions in the images are taken from this model product manual
Barcode scanning
QR code
Barcode
CNC program
Automatic program generation
Drill row shift in X: CNC
Motor shift in Y: CNC
Horizontal drilling height control
Servo, CNC-controlled
Drilling depth control
Servo motor, CNC-controlled
Feed pass
Feed return
CNC system
Operating system
Lubuntu is a fast, lightweight operating system with a clean, easy-to-use interface. It is a Linux system built on the minimal LXDE/LXQT desktop and a set of lightweight applications. Used as a CNC control system it offers these advantages:
Lightweight: needs very little CPU resource to run smoothly and performs especially well when memory is ample.
Fast: it can even run on a computer from 1999.
Excellent stability and security: Linux is open source, all code is published online and seen by programmers worldwide, so defects and vulnerabilities are found quickly, which is where its stability and safety come from.
Built-in 3D drawing
A complete 3D graphics drawing function.
Program generation
Automatic analysis of the input drawing and automatic generation of the machining program, with no manual intervention.
Barcode scanning
The system reads 2D/barcodes and generates the machining program instantly.
Industrial PC with in-house software
Hardware
Captions in the images are taken from this model product manual
Top drill row (motor Y travel and drilling depth: CNC)
Three top vertical drill rows, each driven by twin motors with one 11-spindle drill block per motor.
2 spindles per drill row: 2 rows x 11 spindles/row = 22 spindles
Bottom drill row (motor Y travel and drilling depth: CNC)
Five bottom vertical drill rows, each driven by twin motors with one 11-spindle drill block per motor.
Spindles per drill row: 2 rows x 11 spindles/row = 22 spindles
Vertical drill block
Vertical drill block: 11-spindle block.
Rotates 90 degrees horizontally.
Left horizontal drill block (height adjustment: CNC)
Fitted with 22-spindle horizontal drill blocks.
Right horizontal drill block (CNC suspended, height adjustment: CNC)
It can be raised and lowered to avoid the vertical drill rows when moving,
so repositioning needs no tool or table removal
Fitted with 22-spindle horizontal drill blocks.
Drill bit mounting
Quick-change drill sleeves make tool mounting fast and easy.
Feeding device
Automatic feeder with belt feeding
Feed belt
The feeding device uses a timing belt.
Vertical drill block
Rotates 90 degrees for transverse use; minimum spindle pitch when drill blocks are joined: 32 mm
Through-hole drilling from both sides
Drill rows above and below allow through-hole drilling from both sides; holes are clean with no breakout.
Feeder position adjustment (CNC)
CNC, no manual adjustment: the program calculates the avoidance position automatically
Feed positioning (CNC)
CNC feed positioning without manual intervention; the program calculates the position
Automatic oil pump (CNC)
The lubrication interval is set in the system, simplifying maintenance
Industrial air conditioner
Prevents drives and the PC from overheating
Drilling units travel on imported linear guides
Imported linear guides and ball screws are accurate and long lasting, greatly improving machining precision; low wear saves maintenance and downtime.
Servo control
Servo control: Inovance servo drives and servo motors. EtherCAT communication gives fast, stable control.
High accuracy: closed-loop control of position, speed and torque; no stepper-motor step loss.
High speed: rated speed typically 2000-3000 rpm.
Stable: no stepper-like stepping at low speed; suits applications needing fast response.
High-power transformer
Stabilises voltage and supports heavy loads
Fitted with frequency inverter
I/O modules replace the I/O board
A more stable, durable control system with fewer faults and less production impact
Detail views
Images without captions in the document
Note: the text and images above come from this model product manual and the callouts follow the original document; the diagrams are not to scale and are not site photographs.
Technical specifications
From this model's product document (18 items)
| Processing length | 300–2500 mm |
|---|---|
| Voltage | 380 V,50 Hz,3phase |
| Working width | 32–672 mm |
| Machine weight | approx. 4500 kg |
| Board thickness | 8–50 mm |
| Dimensions | 5000×2530×2200 mm |
| Spindles | 220 stations |
| Capacity | 13–16 pcs/min |
| Max hole diameter | 35 mm |
| DXF import | Yes |
| Max drilling depth | 50 mm |
| MPR import | Yes |
| Spindle speed | 2840 rpm |
| Horizontal rows (left) | 1 |
| Horizontal rows (right) | 1 |
| Upper vertical rows | 3 |
| Lower vertical rows | 5 |
| Air pressure | 0.6–0.8 mpa |
Note: the figures above come from this model's specification sheet; the machine manual or the configuration sheet confirmed by our sales engineer prevails.
Working sequence
Scan a label or call up the program — four steps per batch
Note: the sequence follows the usual order on CNC models; the machine manual prevails.
Applications
Typical work for this machine type
Panel furniture lines
Five-face holes and side bores in cabinet panels
Custom home furnishing
Scan-to-run flexible processing of one-off panels
Cabinets and wardrobes
Multi-face holes in sides, shelves and doors
Technical documents
Manuals and datasheets are available from our sales team with your enquiry
Specification sheet
Detailed figures, installation dimensions and power requirements
Request documentsOperation and maintenance guide
Daily operation routine and routine maintenance notes
Request documentsInspection and warranty
Inspection routine, warranty scope and after-sales support
Request documentsRelated products
Same range and comparable models
New arrivals
The latest machines added to the range
